The Laser Listener
Originally published in Radio Electronics Magazine, October 1987, by Richard L. Pearson
Use a light beam to listen in to anything, anywhere, anytime...
Breaking and entering to plant a listening device is one way to "bug" a room. Unfortunately, it can earn you a long jail term. A better and safer way to bug a room is to use a laser beam to eavesdrop on a window from across the street.
The sound waves generated by nearby conversation will cause the glass in a window to vibrate very slightly. If a laser beam is bounced off the window, its reflection will be modulated by the vibrations. All that's needed to hear what is being said is a demodulating device that extracts the audio from the reflected laser beam. That technique is used by sophisticated "surveillance experts," but you can easily duplicate that feat by using a hobbyist's laser and the inexpensive Laser Listener demodulator shown in Fig. 1. If you need something a little more sophisticated, it can be made part of the riflescope aimed laser-bug system that is shown in Fig. 2.
(Improved PNG Version)
Early Light-Wave Communications
Communication using a modulated beam of light isn't a new idea. In the 1880's, Alexander Graham Bell experimented with something he called a photophone; a device that modulated a beam of sunlight. It had a mouthpiece that concentrated sound energy on a reflecting diaphragm, which, in turn, modulated a beam of sunlight that was aimed at the diaphragm. When a remote receiver consisting of a photovoltaic cell and a sensitive earphone was positioned in the beam, the voice could be heard clearly from the receiver. The aiming problems presented by the movement of the sun, and the interruptions due to clouds and night, probably prevented the commercial exploitation of the device.
But by using coherent light - such as that produced by a continuous-wave laser - the principles used by Bell's device may again be applied in a meaningful way. After all, terrestrial lasers aren't influenced in any way by sunlight or clouds. And perhaps more important, unlike acoustic sound-detection devices, lasers aren't usually subject to interference originating between the sound source and the receiver.
For example, remote sound-pickup devices in the form of directional microphones have been available for many years. Unfortunately, any sound generated between the listener and the sound source usually renders the device useless because the interference is heard at the receiver, and it can be even louder than the source. On the other hand, lasers are not sensitive to sound of any kind between the source and the receiver. However, lasers may be subject to other kinds of interference: For example, AC-powered incandescent lights can produce a hum; gas discharge devices such as fluorescent, mercury, sodium vapor, and neon lights might produce a buzz; and direct sunlight might swamp the laser detector device. Also, where unusually long distances are involved, air currents can add flicker to the laser beam, which on windy days can result in a noise that is similar to that of blowing into a microphone. (But even though sensitive to some kinds of electrically-generated noise, laser-listening devices have an advantage: They can seemingly hear through walls or closed windows, and even selectively monitor only one window of a building from several hundred feet away.)
Commercially available laser sound pickups use a laser device having an output in the infrared region. Because infrared is below the visible portion of the light spectrum, it cannot be seen by humans. However, some commercial devices have a power output rating as high as 35 milliwatts. At such a power level there is clear potential for eye damage if someone in the target area unknowingly stares into the beam, or if the laser is operated carelessy by the user.
Although the details underlying the generation of laser light are beyond the scope of this text, an understanding of some of the characteristics of a laser beam as compared to ordinary light will be helpful in assembling a laser-listener system.
Light is considered to be comprised of packages of energy particles called photons. However, light is also electromagnetic radiation and behaves like radio waves, although at a much higher frequency. The perceived color of visible light is determined by the radiation's wavelength, which is usually given in micrometers. The shorter wavelengths are perceived as violet, the longer wavelengths as red. The spectrum below the visible portion is called infrared; the spectrum above is called ultraviolet.
The light emitted by a conventional incandescent or fluorescent source contains a wide range of frequencies, and the photons are emitted randomly and spontaneously in all directions. On the other hand, in a laser light source the photons are released in one direction, at one frequency, making the laser light highly directional and pure in color. (An analogy would be to liken ordinary light to white noise, while the laser is likened to a sinewave - a single pure tone.) Since all of the light emitted by a laser is coherent (has the same frequency), constructive or destructive interference occurs when two beams of laser light meet at the same place and time (Fig. 3).
As shown in Fig. 3-a, the beams cancel each other when out of phase (destructive interference). As shown in Fig. 3-b, the beams are additive when in phase (constructive interference). It is the interference between the beams that enables the movement of any reflecting surface to be sensed by a device called an interferometer. An interferometer is a beamsplitter - usually a piece of partially-mirrored glass - that deflects only a small part of a beam aimed through the glass. As shown in Fig. 4, it can be used to reflect both the source and the reflected laser beams so that their phasing or amplitude can becompared by a receiver.
The major problems with using interferometry for eavesdropping is that only a part of the laser's energy is directed at the target, limiting the working range, and the interferometer is sensitive to the diffusion of the sounds target's reflections caused by tremors in the mountings of the interferometer, the laser, and the reflective target. For super-snooping, a direct reflection from the target is preferred because the collimated nature (parallelism) of laser light also allows modulation of the beam to occur just as Bell`s photo-phone modulated the sunlight.
The Prototype's Laser
Regardless how we choose to eavesdrop, we must start out with a laser, so we' ll cover the prototype laser bug's unit first. It's a Heathkit model ETS-4200 Laser Trainer, a Helium Neon (HeNe) unit having an output power of 0.9 milliwatts. It has a beam divergence of 1.64 milliradians, which produces a spot of light 1-1/2 inches in diameter at 200 feet. Although 0.9 milliwatts doesn't appear to be much power, it can cause extreme eye damage if allowed to shine or be reflected directly into the eye, or if viewed directly through any optical device such as a telescope, binocular, etc. The beam may be safely viewed only if projected onto a non-reflective surface such as a white sheet of paper.
If you want to keep costs at rock-bottom, or just want the excitement of a complete home-brew project, another alternative is to assemble the helium-neon laser shown in the June 1986 issue of Radio Electronics. Also. if you want to build a laser from your own design, helium-neon tubes are often available from "surplus" distributors.
The Laser Listener's receiver is relatively easy to build and adjust. It is designed to drive a 4 to 20 ohm headphone or speaker, which permits just about any high-fidelity or Walkman-type headphone to be used for monitoring. The circuit shown in Fig. 1, uses a photo transistor (Q1) for a sensor, and has a meter (M1) that indicates the relative signal strength of the reflected laser beam. Because the meter responds only to the amplitude modulation of the reflected laser beam, it is unaffected by ambient light and the relative intensity of the laser beam. An adjustable polarizing light filter can be installed in front of Q1 to avoid swamping of the phototransistor by very high ambient light.
Phototransistor Q1 is an inexpensive type usually called an IR detector, which means that it is specifically sensitive to infrared light. Tests comparing the unit specified in the partlist with other less readily-available and more-expensive devices show no measurable difference in performance in the prototype receiver. No base connection is used for Q1 because the reflected laser light controls the collector current. The audio signal developed across collector load-resistor R1 is coupled by C2 to voltage-controlled attenuator IC1, which has a greater than 30 dB gain variation; It serves as both a preamplifier and as an electronic volume control.
Resistor R2 and capacitor C1 decouple (filter) the power supply voltage to Q1 and IC1. Be sure to take extreme care not to eliminate or accidentally bypass the filter because that will cause unstable operation. The gain of Q1 and IC1 is too great to permit non-decoupled operation from the power supply.
The output from IC1 is fed through C4 to amplifier IC2. Resistor R4 and capacitors C5 and C7, tailor IC2's frequency response and ensure stable operation with varying drive levels and output loads.
The output of IC2 is split into two paths: One goes to output-jack J1 via C6; the other feeds voltage-follower IC3, which drives the meter circuit consisting of D1, D2, C11, R8, and M1. The time constant created by the values of R8, C11 and M1's DC resistance was selected to provide a comfortable damping of the meter pointer's gyrations. The value of C11 may be varied to change the pointer's response. Increasing the value of C11 provides a smoother response; decreasing C11's value will cause the pointer to more closely track the variations in the laser beam's modulation.
The prototype receiver was assembled on a modified Radio Shack type 276-170 pre-drilled PC board, which has strips of copper foil on the underside that connect the component mounting holes. Nothing about the layout is critical as long as you follow the usual precaution of keeping the input and output connections reasonably separated.
Check your parts layout against the foil strips on the underside of the board. If it appears that any will be too long, cut them to size before mounting any components. Cut each foil strip exactly as long as needed so that a foil carrying the input signal doesn't end up running adjacent to an output connection.
For best results when making connection to the foils, use a small pencil-tipped soldering iron and 0.040 diameter rosin-core solder. If your layout requires jumpers between component mounting holes, use #22 solid, bare wire. Insulated jumpers are #22 solid, insulated wire. Connection between the copper foils should be #18 insulated wire because it's a precise push-fit for the holes in the specified prototyping board.
The enclosure is a 6-1/2 x 2-1/8 x 1-5/8 inch aluminum cabinet. Phototransistor Q1 protrudes from one end of the enclosure and is mounted with a dab of household cement. Position Q1 correctly before gluing it in place and be very careful to not get glue on the surface of the lens. Do not use cyanoacrylate-based instant glue because it might cloud the transistor's plastic lens. Output jack J1, gain-control potentiometer R5, and the meter are mounted on the side of the cabinet, so as to encourage the user to face at a right-angle to the source of the laserlight, thereby lessening the change of looking directly into the reflected beam.
The board is mounted in the enclosure with four 3/4 inch 6-32 machine screws. Use 1/8 inch insulated spacers between the board and the enclosure to insure adequate clearance between the enclosure and the board's foil side. A ground lug located at one mounting screw is soldered to the circuit-board's ground foil to provide the ground connection between the board and the cabinet. The connections between the board and the panel mounted components can be #18-22 stranded, insulated wire.
The optical attenuator assembly, for which construction details are shown in Figs. 6 & 7, mounts over phototransistor Q1. Fig. 6 shows how it's installed over Q1: Fig. 7 shows the individual details for each component in the assembly. The front of the assembly is painted flat white so that the reflected laser beam can be easily seen. The attenuator is built in such a way that the phototransistor can see the laser beam directly, or through a combination of one or two polarizing filters. When both filters are in place, rotation of the large-diameter filter-mount will cause a gradual decrease in light transmission (to almost total blockage within 90° of rotation), which allows the receiver to be used over a wide range of light intensities without swamping the photo detector. Fig. 8 shows the installed assembly and the two filters.
The attenuator has an inner filter and an outer filter made from brass telescopic tubing. Each filter consists of two sections: a filter base that is soldered to small mounting plate made from brass sheet (the painted target), and a filter mount that slips over the base. Polaroid fillers cut from neutral-tint polarized sunglasses are cemented to one end of each filter mount to complete the attenuator. When complete, the entire optical attenuator's mounting plate is secured on the enclosure over phototransistor Q1.
We advise that a small speaker be used rather than headphones for the initial tests, then, if a wiring error or a defective component has created an audio oscillator rather than an amplifier, your ears will not be assaulted by a high-level tone or squeal.
With the volume control fully counterclockwise and power-switch S1 set to off, install the battery and connect the speaker. Turn the unit on and point it toward a source of daylight (not direct sun). Advance the volume control to maximum. Correct operation is indicated by a frying noise that sharply diminishes when the light is blocked. The meter-sensitivity control, R8, should then be set so that the meter's pointer just begins to move off the zero calibration. Decrease the gain and point the receiver toward an AC-powered light source, such as an incandescent or fluorescent light, or even an LED driven by an audio oscillator. Those sources should produce a loud hum or tone. Sound will be heard if the LED is driven from an audio amplifier at the correct level. If everything checks OK, assemble the enclosure.
Remote Sound Detection
To use the receiver as a remote sound pickup, you will need a laser and a reflective surface that sound waves will cause to vibrate; the receiver must be positioned so it can "catch" the direct reflection of the laser beam (Fig. 9). A particularly effective reflector for experimental use is a small piece of mirror (about 1/4 x 3/4 inch) cemented to the center of a speaker cone (see Fig. 10). There is no connection made to the speaker. The movement of the speaker cone caused by sound waves is transferred to the mirror-reflector. Which in turn modulates the laser beam.
Due to the varying reflectivety and distances of the targets, the intensity of the light falling upon the detector may vary considerably from setup to setup. That will be readily apparent if the collector voltage of Q1 is measured while the illumination level on Q1 is adjusted. At some point of increasing illumination, the collector voltage will fall sharply and the audio output from the receiver will drop or disappear. The small-diameter polarized filter should then placed over Q1. If more light attenuation is required, slip the large-diameter filter in position and rotate it for maximum sound output.
Thin Is In
The thinner and more responsive to sound the reflective medium is, the greater the laser bug's sensitivity. Most window panes will work. Moving the beam to different spots on the glass can make a dramatic difference in the sensitivity.
For testing, no additional optics are needed for the receiver. Set up any convenient reflector - the mirrored speaker, or even an embroidery hoop holding plastic wrap or Mylar film (see Fig. 10) - aim the laser at the reflector, and then position the reflector so that the beam bounces back to the receiver. If you speak in the room, or play a radio or a tape recorder, the sound will be heard in the receiver's headphones. Another test can be done by modulating the laser with a 1 kHz tone while having an assistant move the target reflector for maximum tone reception - as indicated by maximum volume in the highest meter reading.
A non-adjustable target, such as a window pane, requires that the operator select a site where a direct reflection can be caught. That can be done from hundreds of feet away if conditions are right. Use the modulated beam for setup, and then remove the modulation to listen in. Double-pane glass and storm windows tend to greatly reduce sound transmission to the outer glass. It is possible, however, to aim through the glass to an object within the room, such as the glass front of a china cabinet or a hanging picture. The returned reflection is usually modulated.
At Long Range
At ranges greater than 100 feet or so, or when a high ambient light level obscures the reflected beam, a means must be provided to accurately aim the receiver to the reflected laser. As shown in Fig. 11, the receiving unit of our prototype laser-bug system uses a telescopic gunsight; and that assembly is, in turn, mounted directly on the laser housing as shown in Fig. 2 so both the laser and receiver can be aimed as a single unit.
The design of a combination receiver and laser mounting bracket will depend on the particular laser and scope that's being used. In general, the mounting bracket should be sturdy and have provisions for coarse elevation and azimuth adjustments; all gun scopes have provisions for fine adjustments. The adjustment details for the prototype mount are shown in Fig. 12.
The scope-to-laser alignment is done in two stages. First, the distance from the center of the laser beam to the center of the scope is measured and used as the spacing for the cross marks of the target shown in Fig. 13, which is made from dull, white cardboard. Then, the target is taped to a wall about 50 feet away from the laser assembly. Next, with the scope's cross-hair adjustments at the center of their range, position the laser beam at the center of the lower cross. Looking through the scope, adjust the scope's mounting bracket so that its cross-hairs are close to being centered on the target's upper mark. Making sure that the laser beam stays centered on the lower mark, tighten the mounting bracket's nuts and use the scope's fine adjustments for the final alignment. In this instance, the diffuse reflection of the laser beam from the card should present no eye hazard.
When using the laser/scope assembly, remember that at a range of under 300 feet you must compensate for the aiming error introduced by the offset between the scope and the laser beam centerlines.
Again, let us stress that under no circumstances should the laser beam or its direct reflection be viewed through optical devices of this type because severe damage to the eye can result.
Resistors All resistors are 1/4 watt, 5% unless otherwise noted. R1 2.2 k R2 220 R3 33 k R4 10 R5 10 k miniature potentiometer with SPST switch R6, R7 22 k R8 25 k trimmer potentiometer Capacitors C1, C6, C9, C10 330 µF 16 volts, electrolytic C2, C4 10 µF 16 volts, electrolytic C3 0.001 µF 50 volts, ceramic disc C5 0.68 µF 16 volts, tantalum C7, C8 0.047 µF 50 volts, ceramic disc C11 4.7 µF 16 volts, electrolytic C12 1000 µF 16 volts, electrolytic Semiconductors IC1 RCA SK3891 electronic attenuator (or Motorola MC3340, or ECG ECG829, or NTE NTE829) IC2 National LM380 audio amplifier IC3 National LM741 op-amp Q1 TIL414 NPN phototransistor (Radio Shack 276-145, or L14G3, or equivalent) Dl, D2 RCA SK3090 germanium diode (or ECG109, or NTE109, or 1N34A, or 1N270) Other Components B1 9 volt transistor-radio type battery J1 miniature phone jack M1 250 µA meter S1 SPST switch, part of R5 Miscellaneous Cabinet, pre-drilled PC board, brass sheet and tubing, wire, solder, etc. The following is available from: Dirijo Corp. Box 212, Lowell, NC 28098. A drilled prototype-board with a component layout overlay in place, model LXVR-1. $4.50 plus $2.50 postage and handling. NC residents please add sales tax.
Datasheets & Notes
- L14G3 Silicon Phototransistor (134k PDF)
- MC3340 Electronic Attenuator (80k PDF)
- LM387 Low Noise Dual Preamplifier (125k PDF)
- LM380 2.5 W Audio Power Amplifier (235k PDF)
- Analog Devices AD630 Balanced Modulator/Demodulator A lock-in amplifier can be added to this project to extract the highly-attenuated return modulations.
- Construction Notes
Here are some preliminary pictures of the GBPPR Laser Bounce Listening Device currently under construction. It will be fully documented when complete. Here is the main PIN-diode receiver circuit board. It is based around a VTP1188S photodiode and a LT1055 op-amp feed into an audio-shaping bandpass filter. It uses a magnifying lens mounted in a PVC tube for the main optical guide path.
Notes & Links
- Alternative Laser Receiver/Amplifier Circuit
- Laser Listener by Grand Idea Studios
- An Audio Laser Intercept Demonstration System
- "Laser Ear" Laser Listening Device by Global Security Solutions
- Fusions Group Laser Listening System FGLD-786 High-quality commercial system with a built-in optical stablizer. (Video)
- "SNEAK" Laser Listening Device by Espionage Store
- Laser-3000 Microphone Listening Device Only $51,495.00!
- Spectradome Laser Microphone Includes several audio examples.
- Fusions Group Laser Listening System (Buy It!)
- Laser Eavesdropping Systems by Insight Technologies (Mirror)
- DNP Long-Range Laser Microphone Only 29,000.00 euros!
- Laser Snooper by Nick Shin (Original)
"The PKI 2510 opens up entirely new perspectives in the field of remote acoustic monitoring. The interferometric technology applied here allows to detect and to make audible even the smallest vibrations, e.g. during conversations, by means of an invisible laser beam almost independently of the detection angle and the material of the target. And it really doesn't matter which target material is used. Whether paper, plastics, metal, etc., the technology can even be used through glass panes into closed rooms or a vehicle without problems. The voice information is transmitted as frequency modulation of the laser beam. For this complex interferometric process, the reflection properties / intensity of the reflected light is absolutely unimportant. The PKI 2510 is quickly assembled and ready-to-operate within a few minutes thanks to the parallax-free electronic target sight. Operating distances of up to 150 m with eye-safe lasers class 1 with greatest possible angle independence offering good speech intelligibility and insensitivity to background noise and interference open up versatile applications."
- PKI Electronic Intelligence PKI2510 Opto-Acoustic Laser Microphone
- Laser Microphone Overview from Williamson Labs
- Team LuGER: Laser Listener Senior design project, much more up-to-date. (Slides)
- Sound Retrieval by Demodulating a Reflected Laser Beam From a Vibrating Surface (287k PDF)
- Laser Bounce Listener a.k.a LBR101
- Simple Laser Listener
- The Laser Listener
- Do-It-Yourself Laser Spy Microphone Thread at Schneier on Security.
- DIY Laser Long-Distance Listening Device
- Laser Surveillance System for Under $20
- The Laser Bounce Window Listener by huvanile
- HOW TO: Make a Laser Espionage Microphone by Kiltak
- The Laser Listener - Espionage Technology for $3
- Bugging the Bedroom by Nicholas Pileggi, Esquire, May 1966.
"You're in a room talking to a really trusted friend and no one is within ten miles of you. You lose. The portable laser microphone (left) emits an invisible infrared beam no bigger than a pencil. This beam goes through your glass window and bounces off the mirrored modulator (right), hidden there for the purpose. The beam goes back to the source altered by the sound waves you produce in the room. Miles away a photo amplifier is able to decode your words.
- Optoelectronic Eavesdropping Techniques Practical guide to constructing lightwave transmitters & laser listening systems, by Alan Hoffman
- Laser Microphone Experiment Project 88 from Brad Graham & Kathy McGowan's 101 Spy Gadgets for the Evil Genius (1.8M PDF) (Google Books)
- Laser Window Bounce Listening Device Chapter 13 from Robert E. Iannini's Electronic Gadgets for the Evil Genius (2.5M PDF) (Google Books)
- How to Use a Laser to Eavesdrop on Anyone Excerpt from Lee Lapin's How to Get Anything on Anybody. (1.3M PDF) (Google Books)
- Build Long Range Laser Window Bounce Listeners Plans from Information Unlimited.
- Laser Beam Eavesdropping Real-world info from Kevin D. Murray of Murray Associates.
- Big Brother Gains Mobility in Turkey "A Republican People's Party, or CHP, deputy said 11 vehicles with laser eavesdropping systems were the sources for the wiretapping records that were recently broadcast by the media, daily Hürriyet reported yesterday."
- Laser Listening Device Hack a Day
- Black Hat 2009: Powerline and Optical Keysniffing Use a laser to remotely determine keystrokes. (Notes)
- Laser Surveillance Defeater Hack a Day
- A Simple Laser Microphone for Classroom Demonstration (238k PDF)
- Biasing & Modulating Laser Diodes by John, K3PGP
Laser Audio Surveillance Device by Vincent Amendolare and Wade Sarraf (2M PDF) Ultransensitive Laser Measurements Without Tears Six easily-constructed easily-constructed circuits that can improve the SNR of bright-field laser measurements by as much as 70 dB at low frequency and 40 dB out to 10 MHz, by Phil Hobbs (2.1M PDF) Listening to Neighbors: Lasers and Windows 1998 USENET thread. Laser Beam Eavesdropping - 2010 Simultaneous Remote Extraction of Multiple Speech Sources and Heart Beats from Secondary Speckles Pattern Wide-Angle Laser Audio Eavesdropping Device by Cody Brenneman & Kevin Manelski (2M PDF) Torrey Pines Logic LightSpeed G10 High-end optical communication system. Torrey Pines Logic LightSpeed B10 Optical voice and data communications. VibroMet Long-Range Laser Doppler Vibrometer VibroMet 500V Laser Doppler Vibrometer Polytec OFV-3001 Laser Doppler Vibrometer Manual (2.1M PDF) Laser Microphone by Bob Junior Product Detector using LM1496 Build the Long-Range Laser Spy System (Hack a Day Entry) Integrating LDV Audio and IR Video for Remote Multimodal Surveillance (726k PDF) (Additional Info) The Laser Experimenter's Handbook A learn-by-building course in laser and maser technology, by Frank G. McAleese. (12.3M PDF) Semiconductor Diode Lasers by Ralph Campbell and Forrest Mims (3.9M PDF) German World War 2 Lichtsprechgerät 80/80 Li Spr 80. 2-way audio communication equipment uses infrared light. German Optical Communications This article was taken from the Electronics and Wireless World magazine, August 1985 issue. Laser Vibrometry System for Space Situational Awareness A Laser Microphone Utilizing the sensitivity of a Michelson interferometer to detect vibrations. (6.4M PDF) Remote Laser Interferometry Microphone (100k PDF) Optical Methods for Reproducing Sounds from Old Phonograph Records (2.3M PDF) Apparatus and Method for the Remote Detection of Vibrations of Diffuse Surfaces U.S. Patent 3,952,583 (226k PDF) Laser Interferometry Detection Method/Apparatus for Buried Structure U.S. Patent 4,172,382 (600k PDF) Optical Device for Measuring Surface Roughness U.S. Patent 3,804,521 (637k PDF) Optical Microphone with Vibrating Optical Element U.S. Patent 5,262,884 (594k PDF) Laser Listening Device Detector U.S. Patent 6,114,684 (110k PDF) Voice Monitoring System Using Laser Beam U.S. Patent 6,317,237 (273k PDF) Laser Microphone Caution: Wikipedia Laser Doppler Vibrometer Caution: Wikipedia
Related Audio & Video:
Video Showing the Construction of a Laser Listener Device (YouTube) Lasermikrofon - Interferometer Laser listener made using a Michelson interferometer. (YouTube) CIA Laser Listener Video describing the CIA's version of this device which uses a prism for the return beam. You can get a similar result using certain brands of hair spray on the target window. (YouTube) Laser Microphone for Audio Surveillance via Window Panes (YouTube) Laser Spy Museum exhibit which demonstrates the laser bounce audio surveillance technique. (YouTube)
Other Related GBPPR Projects:
Using Sunlight to Intercept Audio Doppler Stethoscope for E.O.D. Applications Passive Resonant Cavity & "Spycatcher" Technical Surveillance Devices GBPPR Remote Telephone Surveillance Experiments Through-the-Wall Motion Detection Device van Eck-style Radiation Interception Experiments Homebrew Lock-In Amplifier Use this device to significantly increase the performance of a laser bounce listener. GBPPR Interferometric Surveillance Device Experiments